Blog
Mobile home cabinet drawer fronts, made to your sizes

| Drawer fronts | Doors | |
|---|---|---|
| Smallest | 5" x 5" | 5" wide x 8" tall |
| Largest | 49" x 96" | 49" x 96" |
| Minimum charged | 1 square foot | 2 square feet |
Can I replace just the drawer fronts?
Yes, and on their own if that is what you need. There is no requirement to order doors at the same time and no minimum number of pieces.
It is worth saying plainly, because drawer fronts are often what stalls the job. People find doors they can live with, then discover that nothing available comes small enough for the shallow front under the sink, and the whole project waits on one piece.
They are also the half that tends to look worse. Fronts take the hand, the knee and the cleaning cloth in a way doors do not, so in a kitchen where the doors have survived twenty years the fronts are frequently the reason you are reading this.
Why do the sizes never match?
The same reason the doors do not. Cabinets in a manufactured home were built to the plan of that home rather than ordered from a catalogue, so the drawer openings landed wherever the layout put them. A supplier offering fronts in fixed steps is describing its own shelf, not your kitchen.
Drawer fronts make it worse in one specific way: they are often short. A stock range that begins at a height sensible for a door has nothing at all for a front a few inches tall, which is why the search so often ends with nothing to buy rather than with something that nearly fits.
A bank of drawers compounds it again, because the fronts in a bank are rarely all the same height. A deep pan drawer at the bottom, two medium ones above it, a shallow cutlery front at the top — four different numbers, on one cabinet.
What sizes can you order?
From 5 by 5 inches up to 49 by 96 inches, in sixteenth-of-an-inch increments. A front goes smaller in height than a door, which stops at 8 inches tall, because a short front does not need a door’s proportions to hold its shape.
That 5 by 5 minimum is the number that matters in a manufactured home. It is below where most ranges start, and it covers the small fronts that otherwise have no supplier at all.
Is there a minimum on a small front?
Yes, and knowing it in advance saves a surprise. Fronts are priced by the square foot against a one-square-foot minimum, where a door’s minimum is two square feet.
So a front smaller than a square foot is built at the size you ask for and charged at that floor. The floor reflects the work rather than the area: a small piece still takes setup, material and finishing. The useful consequence is that the fronts nobody else will make are the ones the lower minimum was written for.
Five-piece or slab?
A five-piece front is built like a miniature door, with stiles, rails and a centre panel. A slab is one flat piece. On a bank of drawers the choice reads more strongly than it does on a single door, because you see three or four of them stacked.
The trade-offs are set out in five-piece versus slab drawer fronts. One point belongs here rather than there: on a short front a five-piece build leaves very little panel between the rails, so below a certain height a slab is usually the better-looking piece as well as the simpler one. If you are not sure where your fronts fall, send the sizes and ask before ordering.
Which way should the grain run?
This is the decision most likely to be missed, and the one that cannot be fixed afterwards.
Every piece is made with vertical grain by default, matching the doors. Horizontal is available on request, and it has to be asked for in the order notes, because nothing on the order form asks the question.
A bank of drawer fronts is exactly where the choice shows. Vertical matches the doors above and beside them, which is why it is the default. Horizontal runs the grain across the width of each front and reads as continuous down the bank, which some people prefer on a run of three or four.
Neither is wrong, and on a painted finish it barely matters. On anything where the timber shows it matters a great deal — and a run ordered the wrong way round is a remake rather than a disappointment. Decide it before you order, and write it in the notes.
How do I measure them?
Measure the fronts you have rather than the openings. The front overlaps the opening by an amount somebody decided when the cabinet was built, and copying the piece keeps that decision intact. How to measure for replacement cabinet doors covers the method, and it applies to fronts unchanged.
Two habits pay off in a manufactured home. Measure every front separately rather than assuming a bank matches, because they usually do not. And record the numbers to the sixteenth rather than rounding, since that is the increment they will be built to — a measurement rounded to the nearest quarter throws away accuracy the shop could have used.
If a front is cupped or swollen, measure a neighbour that is not, or measure the opening and say that is what you have done.
How long do they take, and what next?
About two weeks from order to shipped, the same as doors, and the same across every door family. Fronts arrive finished, and bored for your hardware if you asked for it.
Before you order: write down every front, width and height, to the sixteenth; decide five-piece or slab; decide grain direction and note it. Then price them, choosing Drawer Front rather than Door, where the calculator sits on the product itself. If anything is unclear, ask first — a question is free and a remake is not.
Frequently asked questions
Can I order drawer fronts without ordering doors?
Yes. Fronts can be ordered on their own, in any quantity, with no minimum number of pieces.
What is the smallest drawer front you can make?
5 by 5 inches. That is smaller than the smallest door, which is 5 inches wide by 8 inches tall, because a short front does not need a door’s proportions to hold its shape.
Is there a minimum charge on a small front?
Yes — one square foot, against two square feet for a door. A front smaller than that is built at the size you ask for and charged at the one-square-foot minimum.
Should a short drawer front be five-piece or slab?
Usually slab. A five-piece build needs room between the rails for a centre panel, and on a short front there is very little left. Send the sizes if you would like it checked before ordering.
Which way does the grain run?
Vertically by default, matching the doors. Horizontal is available on request and has to be asked for in the order notes, because the form does not ask. On a bank of fronts it is a visible choice and it cannot be changed after the pieces are made.
How long do drawer fronts take?
About two weeks from order to shipped, the same as doors, across every door family.